Racedom Blog
  • Blog
    • Blog Articles
  • Shop
  • Gallery
  • Contact
  • About
  • Girls
  • Videos
  • TikTok
defi advance
June 19, 2020

Unboxing the Defi Advance Control Unit for Gauges

Defi Link Advanced System is a sophisticated unit that is required when setting up Defi Advanced BF and Advanced CR Meters.

Defi Advance Control Unit for Gauges

Up to 7 gauges and displays can be connected and controlled by this one unit. Defi daisy chain system into this control unit makes wiring and setting up your gauges simple and clean. Driving data can be stored and played back from up to 3 minutes with play, pause, forward, and rewind functions during initial playback. This is a unit that must be purchased along with any Defi-Link gauges that require the Advanced System.

New features of the 7703

  • Not only minimum values but also maximum values can be displayed in peak modes of oil pressure and fuel pressure.
  • The illumination of the switch unit is automatically turned on/off if ADVANCE ZD is installed.

This unit will not work with older Defi BF gauges or the Racer series.

Quick Info

  • For Advance BF & CR Gauges

  • 1 Unit Required

  • Run up to 7 Gauges

Summary

Defi-Link ADVANCE SYSTEM is the next generation system that adopted interactive communication.

Defi-Link ADVANCE Control Unit is necessary to operate ADVANCE gauges and displays.

Part No. DF07703 (From February, 2012) / DF07701 (End of life in December, 2011)

*Defi-Link ADVANCE Control Unit is expressed as ADVANCE Control Unit or ADVANCE unit.

Main specifications, functions, and features

  • ADVANCE System
  • Necessary for ADVANCE gauges and displays
  • Switch unit attached
  • Driving data can be recorded & replayed
  • Illumination ON/OFF: interlocked with vehicle illumination switch
  • Illumination color: White (switch)
  • Indicator output

Features

  • An interactive communication advanced system is implemented.
  • ADVANCE Control Unit can control up to 7 Defi-Link Meter ADVANCE CRs and ADVANCE BFs all in at a time. (Ex. 4 ADVANCE CRs and 3 ADVANCE BFs)
  • Gauges can be controlled from distance with the included switch unit.
    switch illumination
  • Opening and closing modes can be selected from 2 variations.
  • The installation of additional gauges is easy. Just connect it with the other two gauges and attach the wire to Advance Control Unit.
  • The power source indicator (blue LED) assures correct wiring.
  • Warning by buzzer sound when the warning LED is on (buzzer sound can be turned on / off).
  • Peak value and warning value during driving are stored. Driving data can be stored and replayed up to 3 minutes.
  • With both fuel pressure gauge and turbo installed, differential pressure can be monitored on the fuel pressure gauge screen.
  • ADVANCE Control Unit is threadably mountable.

Specifications

The differences between DF07703 and DF07701

<How to recognize the models>

“03” is appeared in the lower right on the front panel of unit: DF07703
Nothing is appeared in the lower right on the front panel of unit: DF07701

difference between 7703 and 7701

<New functions on DF07703 (Functions which are added to 07701)>

    • Not only minimum values but also maximum values can be displayed in peak modes of oil pressure and fuel pressure.
    • The illumination of the switch unit is automatically turned on/off if ADVANCE ZD is installed.

 

Specifications in mm (inches)

ADVANCE Control Unit

ADVANCE unit size

1 Switch unit(white)
2 Speed & Tachometer signal wire(blue)
3 Exhaust temp sensor wire(black)
4 Water temp sensor wire(pink)
5 Oil temp sensor wire(red)
6 Fuel press sensor wire(red)
7 Oil press sensor wire(white)
8 Turbo/In-Mani sensor wire(light blue)
9 Power source wire(beige)
10 Meter wire(white)
11 Meter wire(white)

Switch unit

ADVANCE switch size

Other specifications

Power supply
voltage
10V to 16V DC (12V vehicle only)
Current consumption Maximum during 7 gauges are connected
+B 2A(IGN ON), 5mA(IGN OFF)
ILM 800mA
The applicable number of cylinders 1,2,3,4,5,6,8
Note *Products are for only on vehicles with a 12V electrical system. Never use products on 24V vehicles.
*Products can not be installed in altered vehicles.
*To install pressure gauges or temperature gauges, proper sensor attachments are necessary. The thread sizes of sensors are 1/8PT.

ADVANCE System connection

The Defi-Link ADVANCE system allows gauges and displays to be attached to the ADVANCE control unit with a single “DAISY CHAIN” wiring system.
ADVANCE gauges, displays, and Control Unit are equipped with microcomputers. Distant gauges and displays can be operated at hand.

The system is also designed to allow all sensors to be attached to the ADVANCE control unit, so that gauges and displays can be mounted separately without the need for multiple tubing or wiring to each gauge.

daisy chain

  • *ADVANCE System (from 2009) and Defi-Link System (from 1998) are not compatible. Control unit and sensor wires for Defi-Link System cannot be used for ADVANCE System except some common sensors and extension wires.
  • *To operate ADVANCE gauges and displays, ADVANCE Control Unit is necessary.

Wiring diagram

ADVANCE system

  • ※One Control Unit can control up to 7 ADVANCE gauges & displays in all. (except DSDF)
  • ※All the gauges(&displays) can be connected to both Meter Output connectors.
  • ※Different color gauges can be connected.
  • ※The same variety of gauges cannot be connected. (Ex. Two turbo gauges cannot be connected.)
  • ※More than 2 Displays(ZDs) can be connected.
  • ※Gauges(& displays) can be connected in any order.
  • ※Smart Adapter and DSDF need to be connected to the end of the meter line because they have only one connector for meter wire.

Video

SHOP NOW

Spread the love
Unboxing the Phormula Knock Analyser Pro AEM Infinity-708/710/712 Full Universal Harness

Related Posts

AEM V3 Water/Methanol Standard Controller Kit Internal MAP with 35psi max

New Products, Motorsport, Performance

AEM V3 Water/Methanol Standard Controller Kit Internal MAP with 35psi max

AEM High-Flow Low-Current WMI Solenoid

New Products, Motorsport, Performance

AEM High-Flow Low-Current WMI Solenoid

AEM V3 Water/Methanol Injection 1.15 Gallon Tank Kit with Conductive Fluid Level Sensor

Motorsport, Performance

AEM V3 Water/Methanol Injection 1.15 Gallon Tank Kit with Conductive Fluid Level Sensor

Categories

  • Black Friday
  • Early Bird Offers
  • Holiday Clearance
  • Models
  • Motorcycle
  • Motorsport
  • New Products
  • Performance
  • Videos

Recent Posts

  • AEM V3 Water/Methanol Standard Controller Kit Internal MAP with 35psi max
  • AEM High-Flow Low-Current WMI Solenoid
  • AEM V3 Water/Methanol Injection 1.15 Gallon Tank Kit with Conductive Fluid Level Sensor
  • AEM V3 Water/Methanol Nozzle and Controller Kit, Standard Controller Internal MAP
  • AEM V3 Water/Methanol Injection Kit, Standard Controller Internal MAP

Popular Posts

  • AEM V3 Water/Methanol Standard Controller Kit Internal MAP with 35psi maxAEM V3 Water/Methanol Standard Controller Kit Internal MAP with 35psi max
  • AEM High-Flow Low-Current WMI SolenoidAEM High-Flow Low-Current WMI Solenoid
  • AEM V3 Water/Methanol Injection 1.15 Gallon Tank Kit with Conductive Fluid Level SensorAEM V3 Water/Methanol Injection 1.15 Gallon Tank Kit with Conductive Fluid Level Sensor
  • AEM V3 Water/Methanol Nozzle and Controller Kit, Standard Controller Internal MAPAEM V3 Water/Methanol Nozzle and Controller Kit, Standard Controller Internal MAP
  • AEM V3 Water/Methanol Injection Kit, Standard Controller Internal MAPAEM V3 Water/Methanol Injection Kit, Standard Controller Internal MAP

Like Us On Facebook

Facebook Pagelike Widget

Youtube Channel

TIKTOK VIDEOS

View on TikTok

Youtube Subscribe

Youtube Subscribe
© Racedom Blog 2021
Powered by Racedom